Uretyco
Make it now
PA12 (Nylon 12)

PA12 (Nylon 12)

Plastics
PA12NylonMJFSLS

PA12 (Nylon 12) reference for MJF and SLS: typical printed properties, powder-bed design rules, tolerances, finishing and cost drivers, and comparison with PA11, CF-PA12, TPU 95A and ABS.

PA12 (polyamide 12, Nylon 12) is the default material for powder-bed fusion. MJF and SLS build it layer by layer from powder without support structures, giving strong, tough parts with nearly direction-independent strength, good chemical resistance and the lowest moisture uptake of the common nylons. MJF parts come out dark grey, SLS parts off-white.

Choose PA12 for functional prototypes, housings, ducts, brackets, clips and low-volume end-use parts with complex geometry, internal channels or consolidated assemblies. It does not replace machined metal or high-temperature plastics, and as-printed surfaces are slightly grainy. On Uretyco it is offered for MJF and SLS; PA12 and PA6 filament for FDM can also be requested.

Mechanical and physical properties

PropertyTypical valueNotes
Tensile strength≈ 48 MPaMJF and SLS, per Uretyco's MJF/SLS guide; similar in all build directions.
Elongation at break≈ 15–24%MJF ≈ 20%, SLS ≈ 24% in the XY plane; lower in the build (Z) direction.
Tensile modulus≈ 1.6–1.8 GPaFlexible compared with ABS or POM; stiffen with ribs or use CF-PA12.
Density (printed part)≈ 0.93–1.01 g/cm³Slightly porous; SLS parts typically at the lower end.
Melting point≈ 175–187 °CDepends on the powder.
Heat deflection temperature (HDT)≈ 85–95 °CAt 1.8 MPa; ≈ 150–175 °C at 0.45 MPa.
Max. continuous service temperature≈ 80–100 °CLower for parts under sustained load.
Water absorption≈ 0.5–1.5%From 50% RH to saturation; far lower than PA6 or PA66, so dimensions stay stable.
Layer thicknessMJF 80 µm, SLS 100–120 µmPer Uretyco's MJF/SLS guide; layer steps are visible on shallow slopes.
FlammabilityUL 94 HBStandard powders; flame-retardant powders exist for specific applications.
Typical values, not design allowables

Typical room-temperature values for printed PA12, measured mainly in the XY plane. Results vary with machine, powder refresh rate, orientation and wall thickness, and absorbed moisture slightly lowers stiffness. For load-bearing parts, validate printed samples and use the data sheet of the specific powder named in your quote.

Designing PA12 parts for MJF and SLS

MJF and SLS need no supports: unfused powder carries overhangs, so geometric freedom is high. The limits come from depowdering, heat and part thickness. The rules from Uretyco's MJF/SLS design guide:

  • Walls: at least 0.8 mm for cosmetic features and 1.5 mm for functional, load-bearing walls; stiffen with ribs rather than thick sections.
  • Pins and holes: unsupported pins at least 1.0 mm in diameter and no longer than 8 mm; holes from 0.5 mm. For clean threads, print bores of at least 1.5 mm and tap after printing, or use heat-set inserts.
  • Hollows: every hollow needs an escape hole for unfused powder, ideally two on opposite sides; 4 mm diameter is the minimum, 6–8 mm for internal volumes above 50 cm³.
  • Assemblies and fits: keep at least 0.5 mm between parts printed together so they do not fuse; add 0.4 mm clearance for sliding fits and about 0.1 mm interference for press fits.
  • Thick sections: bulky solids cool slowly, can warp and cost more; hollow or lattice them where possible.

Mechanical results from MJF and SLS are similar. MJF generally wins on speed and surface smoothness, while SLS retains advantages for some specialty materials; if either is acceptable, let the quote compare them.

Tolerances and surface finish

Plan for ±0.3 mm or ±0.3% on each linear feature, as Uretyco's MJF/SLS guide states; long flat parts and thick sections can deviate more through warpage. As-printed surfaces are slightly grainy. Bores, sealing faces or bearing seats that need better accuracy can be reamed or machined after printing; mark them on a drawing. Final values are confirmed in the quote and the order.

Nylon filament for FDM

Nylon is also printed as filament by FDM, mostly as PA6 or PA6 copolymers and less often as PA12, either unfilled or filled with carbon or glass fiber. The polymer family is the same as in powder-bed PA12, but the parts behave differently: FDM builds them from extruded beads and needs supports for overhangs, so strength depends on direction and layer lines stay visible. Points to weigh:

  • Moisture: nylon filament absorbs water from the air within hours, so it is dried before printing and kept dry during the build; wet filament bubbles, strings and bonds poorly. PA6 takes up about 2.5–3% water at 50% RH, PA12 well under 1%, so printed PA6 parts change stiffness and dimensions noticeably as they condition, while PA12 stays more stable.
  • Warping: nylon shrinks as it crystallizes, so long, flat parts lift at the corners. A heated bed, an enclosed chamber and a suitable bed surface are needed; ribs and rounded corners reduce the risk, and fiber-filled grades warp much less.
  • Layer adhesion: nylon bonds better between layers than most filaments, but strength across the layers (Z) remains lower than in the layer plane. Powder-bed PA12 is nearly isotropic, so it is the safer choice when loads act in several directions.
  • When FDM nylon makes sense: single parts and quick functional prototypes, large, simple parts that exceed powder-bed build volumes or would be costly there, and fiber-filled grades for stiff jigs and fixtures. For complex geometry, internal channels, many parts per build or consistent properties, PA12 by MJF or SLS remains the better route. FDM nylon is a specialized option; grade, feasibility and lead time are confirmed in the quote.

Finishing options

FinishCost adderNotes for PA12
Standard depowderedBaselineGrainy, matte; MJF dark grey, SLS off-white.
Bead blast+5–10%Uniform matte surface; the usual cosmetic baseline.
Dyeing (black, grey, blue)+10–15%Consistent color that hides build lines; adds no thickness.
Vapor smoothing+15–30%Sealed, smooth, semi-glossy surface that is easier to clean.
Spray paint + clear coat+30–50%For color-critical end-use parts; mask mating faces.
Hollow parts to save cost

MJF is priced by the powder consumed and the build height, so hollowing thick volumes can cut part cost by 30–50%. Combine hollows with escape holes and, where stiffness matters, internal lattices.

Cost and lead-time drivers

Powder-bed parts are priced mainly by volume, height in the build and post-processing, not by geometric complexity. The main levers:

  • Volume and build height: hollows, lattices and thinner walls lower cost; orientation changes build height.
  • Build packing: how the build tray is packed affects when a powder-bed part ships; a flexible deadline helps.
  • Finishing: dyeing, vapor smoothing and painting add cost (see table) and batch time.
  • Quantity: below roughly 5,000 units, MJF is often more cost-effective than steel injection tooling; Uretyco's quoting engine compares both when the part is feasible.
  • Documents: inspection reports and material documentation are opt-in and can extend the lead time. Request them at quote time.

PA12 vs. common alternatives

MaterialStiffnessElongation at breakBest forProcesses on Uretyco
PA12≈ 1.6–1.8 GPa≈ 15–24%General functional partsMJF, SLS
PA11Similar≈ 45%Snap-fits, living hinges, impactSLS, MJF
CF-PA12Much higher≈ 3–6%Stiff brackets and toolingMJF, SLS
TPU 95ARubber-like (Shore 95A)Very highSeals, grips, cushioningMJF, FDM, injection molding
ABS≈ 2.0–2.4 GPa≈ 10–50%Molded housings in volumeCNC, injection molding, FDM

PA11 trades a little stiffness for much higher elongation and impact resistance; CF-PA12 does the reverse. For a frozen design in quantities beyond a few thousand parts, an injection-molded resin usually becomes cheaper.

When not to choose PA12

Common mismatches

Tolerances tighter than about ±0.3 mm without post-machining: use CNC. Continuous service above about 100 °C, or loaded parts close to it: consider PEEK or metal. Glossy cosmetic surfaces straight from the machine: use molding, or plan vapor smoothing or paint. Very stiff, thin brackets: use CF-PA12 or aluminum. Pressure-tight or food-contact parts as printed: the surface is slightly porous, so seal it, validate it and confirm the powder's suitability.

Typical applications

  • Functional prototypes and end-use housings.
  • Ducts, manifolds and parts with internal channels.
  • Brackets, clips, snap-fits and cable guides.
  • Jigs, fixtures and assembly aids.
  • Bridge production ahead of injection tooling.
  • Service and replacement parts for low-volume or legacy products.

Specifying PA12 on Uretyco

  1. 1
    Select PA12 and the process

    MJF for speed and smoother surfaces, SLS where the quote or a specific powder favors it; leave the choice open if either is acceptable.

  2. 2
    Upload STL, 3MF or STEP

    STEP is meshed server-side. Add a short note on intended use (cosmetic, structural, food contact) so the platform can suggest finish and material options.

  3. 3
    Choose finish and color

    Standard depowdered, bead blast, dyed black, grey or blue, vapor smoothed or painted.

  4. 4
    Add a drawing for critical features

    Mark faces to be reamed or tapped, inserts and any inspection requirements.

FAQ

MJF or SLS: which should I choose?

For PA12 the mechanical results are similar. MJF is usually faster and gives a smoother, dark grey surface; SLS gives off-white parts that suit light paint colors and offers more specialty materials. If both are acceptable, say so and let the quote compare cost and lead time.

Are PA12 parts watertight?

As printed, thin walls can weep under pressure because the surface is slightly porous. Thicker walls help, and vapor smoothing seals the surface. Test pressure-bearing parts before ordering a batch.

Can PA12 replace injection-molded parts?

Often, at low to mid volumes. Below roughly 5,000 units, especially with complex assemblies or many variants, MJF is frequently cheaper than steel tooling. Check that printed properties and surface quality meet the requirement; molded resins are smoother and can be stiffer.

Related materials

Was this page helpful?

Can't find what you need? Contact our team for expert assistance with your manufacturing project.

Contact our team