AZ31B (UNS M11311) is a wrought magnesium alloy with about 3% aluminum and 1% zinc, supplied as sheet, plate and extruded bar. At 1.77 g/cm³ it is the lightest structural metal in routine production: about 35% lighter than aluminum and less than a quarter of the weight of steel. It is also among the easiest metals to machine, with low cutting forces and very high cutting speeds.
Choose AZ31B when weight is the dominant requirement and the part lives in a dry or well-protected environment: hand-held housings, camera and instrument bodies, portable fixtures and motorsport components. Its strength is below 6061-T6, its corrosion resistance is poor without a coating system, and machining needs a supplier equipped for magnesium swarf, so it is rarely the default choice.
Mechanical and physical properties
| Property | Typical value | Notes |
|---|---|---|
| Tensile strength (Rm) | ≈ 240–290 MPa | ≈ 260 MPa for extrusions (F), ≈ 290 MPa for H24 sheet and plate, lower when annealed (O). |
| Yield strength (Rp0.2) | ≈ 150–220 MPa | In tension. Compressive yield of extrusions can be about half the tensile value; check parts loaded in compression or bending. |
| Elongation at break | ≈ 12–21% | Highest in the annealed condition. |
| Hardness | ≈ 50–75 HB | Higher in the H24 temper. |
| Elastic modulus | 45 GPa | About two-thirds of aluminum; thicken sections for equal stiffness. |
| Density | 1.77 g/cm³ | ≈ 65% of aluminum, ≈ 23% of steel. |
| Thermal conductivity | ≈ 96 W/m·K | Good heat spreading for electronics housings. |
| Thermal expansion | ≈ 26 µm/m·K | Slightly above aluminum; allow for it in fits against steel parts. |
| Melting range | ≈ 605–630 °C | Solid parts are hard to ignite; chips and dust are not (see below). |
| Service temperature | Up to ≈ 100–150 °C | Strength falls and creep rises above this range. |
Typical room-temperature values; actual values depend on product form (sheet, plate, extrusion), temper and thickness. For design, use the minimums of the governing standard (e.g. ASTM B90 for sheet and plate, ASTM B107 for extrusions) or your material certificate.
Machining AZ31B
Magnesium cuts cleanly at high speeds with little tool wear and leaves an excellent surface straight from the machine. Its machining practice is shaped by one fact, covered in the next section: chips and fines can ignite. Design-side points:
- Stiffness: with a modulus of 45 GPa, thin walls deflect and chatter sooner than in aluminum. The CNC Design Guide's 0.8 mm minimum for aluminum is not a safe target here; plan thicker walls and ribs.
- Very fine finishing: light finishing passes produce thin chips, which ignite most easily. Unusually fine surface requirements or heavy hand finishing add risk and cost.
- Edges: specify edge breaks on the drawing; manual deburring and sanding create fine dust that has to be controlled.
- Threads: magnesium threads are soft; use threaded inserts for load-bearing or frequently assembled joints.
Chip and dust fire safety
A solid magnesium part is hard to ignite because heat conducts away quickly. Chips, swarf, fines and grinding dust are different: their large surface area lets them reach ignition temperature from friction, a dull tool or a spark, and burning magnesium is extremely hot. Shops that machine magnesium routinely follow established practice, typically referenced to NFPA 484 (combustible metals) or equivalent national rules:
- Sharp tools, positive geometry and a chip load high enough to make thick chips; no dwelling or rubbing.
- Dry machining or neat mineral-oil cutting fluids are common. Water-based coolants are used only with formulations intended for magnesium, because wet fines slowly release hydrogen.
- Frequent removal of chips from the machine into covered, dry, clearly marked metal containers, kept separate from other metal swarf.
- No water, CO2 or standard ABC extinguishers on a magnesium fire; Class D dry-powder agents or dry sand are used.
- Grinding, sanding and polishing dust captured by collectors designed for magnesium and never mixed with dust from other metals.
Select AZ31B explicitly in the quote rather than describing the part as aluminum-like. Uretyco matches orders by process capability and material access, and magnesium needs a supplier set up for its chips, which can narrow the options and add lead time.
Corrosion protection and finishes
Magnesium is the most electrochemically active structural metal. Bare AZ31B tarnishes in air and corrodes quickly in humidity, salt or condensation, and it corrodes sacrificially when in electrical contact with steel, stainless steel, copper alloys and, to a lesser degree, aluminum.
| Finish | What it adds | Notes for AZ31B |
|---|---|---|
| As-machined | Lowest cost | Only for dry indoor use or short-lived prototypes; surfaces dull and stain. |
| Chemical conversion coating | Corrosion base and paint primer | Chromate or chrome-free treatments; thin, and limited protection on its own. |
| Magnesium anodizing or PEO | Hard ceramic-like layer, wear and corrosion resistance | Processes specific to magnesium; aluminum Type II/III anodizing does not apply. Usually sealed or painted for outdoor use. |
| Paint or powder coat over a conversion coating | Color and the strongest barrier | The usual system for outdoor or humid service; mask contact faces and threads. |
Use aluminum (5xxx or 6xxx) or insulating washers and sleeves between magnesium and steel or stainless fasteners, seal faying surfaces and avoid shapes that trap water. Specify the complete finish system on the drawing, because the choice of finishes for magnesium is narrower than for aluminum.
Cost and lead-time drivers
AZ31B stock costs more per kilogram than common aluminum alloys, but parts are light and machine quickly. The real drivers are supplier availability and finishing:
- Material access: magnesium bar and plate are less widely stocked than aluminum; special or imported stock adds lead time, whereas stocked material is usually faster.
- Supplier set: fewer shops are equipped for magnesium, which narrows supplier matching and can lengthen the lead time.
- Finishing: conversion coating, magnesium anodizing and paint are specialist processes with their own batch times.
- Documents: material certificates and inspection reports are opt-in and can extend the lead time; request them at quote time.
AZ31B vs. lightweight alternatives
| Material | Density | Strength (Rm) | Specific strength (MPa per g/cm³) | Corrosion | Notes |
|---|---|---|---|---|---|
| Magnesium AZ31B | 1.77 g/cm³ | ≈ 260 MPa | ≈ 147 | Poor; needs a coating system | Lightest; chip fire precautions. |
| Aluminum 6061-T6 | 2.70 g/cm³ | ≈ 310 MPa | ≈ 115 | Good | The default; anodizes well. |
| Aluminum 7075-T6 | 2.81 g/cm³ | ≈ 570 MPa | ≈ 203 | Fair; needs protection | Strongest common aluminum. |
| Titanium Grade 5 | 4.43 g/cm³ | ≈ 950 MPa | ≈ 214 | Excellent | Costly and slow to machine. |
In specific stiffness (modulus divided by density) all four metals are almost identical. Magnesium's real advantage is in panels and housings loaded in bending: at equal weight, a magnesium wall can be about 50% thicker than an aluminum one, and because bending stiffness grows with the cube of thickness, it ends up roughly twice as stiff.
When not to choose AZ31B
Wet, salty or outdoor service without a complete coating system and galvanic isolation. Sustained temperatures above about 100–150 °C. Parts that need heavy hand polishing or grinding. Highly stressed parts, or parts loaded mainly in compression: 7075-T6 or titanium are stronger. Tight schedules where a widely stocked aluminum alloy would do.
Typical applications
- Hand-held instrument and electronics housings.
- Camera, lens and optical-instrument bodies.
- Drone, robotics and motorsport brackets and covers.
- Portable jigs, fixtures and gauges that are lifted by hand.
- Engraving and embossing plates.
Specifying AZ31B on Uretyco
- 1Select AZ31B and the product form
Sheet or plate (H24 or O) or extrusion (F); state the form if properties depend on it.
- 2Upload STEP plus a 2D drawing
Show the complete finish system, masked contact faces and insert locations.
- 3Describe the operating environment
Indoor, outdoor, humid or salt exposure decides the coating system and fastener isolation; add it to the order notes or tell the AI assistant.
- 4Request documents at quote time
Material certificates and inspection reports are opt-in and must be planned before production.
FAQ
Is a finished magnesium part a fire hazard?
In normal use, no: solid parts are hard to ignite, and the risk lies in chips and dust during manufacturing. In a fire, however, magnesium parts can burn intensely once ignited, so check any flammability requirements that apply to your product.
Can AZ31B be anodized like aluminum?
Not with aluminum Type II or III processes. Magnesium has its own anodizing and plasma electrolytic oxidation (PEO) processes, normally followed by sealing or paint for corrosion protection.
AZ31B or AZ91D?
AZ91D is the common die-casting alloy for high-volume magnesium housings. AZ31B is the wrought alloy for parts machined from sheet, plate or bar, which suits prototypes and low volumes.
Can AZ31B be welded?
Yes, typically by TIG with a magnesium filler. Welded assemblies usually receive a stress-relief treatment to reduce the risk of stress-corrosion cracking.
Related resources
- Aluminum 6061-T6The default lightweight structural metal.
- Aluminum 7075-T6Higher strength at slightly more weight.
- Titanium Grade 5Strength and corrosion resistance, at a cost.
- CNC Design GuideTolerances, walls, threads and setups.
- CNC MachiningProcess overview, files and cost drivers.
- Surface FinishingCoatings, masking and quality notes.
- Lead Times & Supplier MatchingHow material access and capability affect delivery.
- Technical Drawings & TolerancesWhat belongs on the 2D drawing.
Related materials
Can't find what you need? Contact our team for expert assistance with your manufacturing project.







