Galvanized steel on this page means continuously hot-dip zinc-coated low-carbon steel sheet, specified as DX51D+Z to EN 10346 or SGCC to JIS G3302 (ASTM A653 CS is the US counterpart). The zinc protects the steel in two ways: as a barrier, and sacrificially, corroding first so that scratches and the cut edges of thin sheet stay protected for a while.
Choose it for cost-sensitive bent sheet-metal parts that must cope with humidity or outdoor exposure: cabinets, ducting, brackets, covers and machine housings. It is about three times heavier than aluminum and less durable than stainless steel in aggressive environments, but it is usually the cheapest corrosion-protected sheet.
Mechanical and physical properties
| Property | Typical value | Notes |
|---|---|---|
| Tensile strength (Rm) | 270–500 MPa | Specified range for DX51D (EN 10346); actual values vary by mill. |
| Yield strength | Not specified for DX51D | Check the certificate. For a guaranteed yield, specify a structural grade S220GD–S350GD (number = minimum yield in MPa). |
| Elongation at break | ≥ 22% | A80 minimum for DX51D. |
| Elastic modulus | ≈ 200–210 GPa | About three times aluminum: thinner sheet gives the same stiffness. |
| Density | 7.85 g/cm³ | About 2.9× aluminum. |
| Thermal conductivity | ≈ 50–60 W/m·K | Low-carbon steel; about one-third of aluminum alloys. |
| Thermal expansion | ≈ 12 µm/m·K | About half of aluminum. |
| Zinc coating | Z100–Z275 common | Total g/m² on both sides: Z100 ≈ 7 µm and Z275 ≈ 20 µm per side. |
| Coating service temperature | Up to ≈ 200 °C | Continuous; the coating degrades at higher temperatures (zinc melts at 420 °C). |
Values are typical or specification ranges for DX51D+Z sheet; actual properties vary with thickness, coating and mill. For structural calculations, use a structural grade with guaranteed minimums (e.g. S250GD+Z or S350GD+Z to EN 10346) and the values from your material certificate.
Laser cutting, bending and joining galvanized sheet
Galvanized sheet runs through the same laser-cutting and press-brake steps as mild steel, and Uretyco's sheet-metal rules for mild steel apply: model an inside radius equal to the thickness with K ≈ 0.42 up to 2 mm, make holes at least the sheet thickness in diameter, keep them 2× thickness from edges and 3× thickness from the bend tangent line, leave 6× thickness plus the radii between bends, and add bend reliefs at least 1× thickness wide and 1.5× thickness deep. Specific to the zinc layer:
- Cut edges are bare: laser cutting leaves an uncoated steel edge. The surrounding zinc protects thin-sheet edges for a while, but in wet or outdoor service they eventually show red rust unless the part is painted or powder coated after fabrication.
- Tight bends: very tight bends can crack the zinc on the outside of the bend; at an inside radius equal to the thickness, standard coatings form well.
- Welding: welding burns off the zinc and releases zinc-oxide fume, which is hazardous to breathe. Weld zones need fume extraction and local coating removal, and the zinc must be restored afterwards, usually with zinc-rich paint. Spot welding, clinching, rivets and self-clinching hardware avoid most of this.
- Appearance and storage: the coating can show a crystalline spangle, and parts stored wet or stacked in condensation develop white rust (wet-storage stain). State on the drawing if appearance matters.
- Coating class: name the coating you need, for example Z275 for outdoor parts. In a given environment, coating life is roughly proportional to zinc thickness.
Tolerances and surface
Uretyco's sheet-metal guide gives these achievable values: ±0.10 mm on laser-cut edge lengths and hole diameters (holes for fits are drilled), bend angles ±1° as standard and ±0.5° on request, hole positions after bending ±0.5 mm by default, and 1–2 mm of possible warp on parts longer than 300 mm. Bent dimensions vary more than flat cuts, so control key formed dimensions on the drawing. Ask for deburring on handled edges. Final values are confirmed in the quote and the order.
Finishing options
Galvanized parts are often used as-is. For color, cosmetic surfaces or longer outdoor life, paint or powder over the zinc (a duplex system) outlasts either layer alone, provided the zinc surface is pretreated for adhesion.
| Finish | What it adds | Notes for galvanized sheet |
|---|---|---|
| As galvanized | Lowest cost | Spangle and handling marks visible; cut edges and welds are bare. |
| Powder coat (duplex) | Color, edge and weld protection | Needs zinc-specific pretreatment; trapped gas can cause pinholes. Uretyco's finish guide recommends zinc or e-coat under powder for outdoor or marine use. |
| Wet paint | Color, touch-up | Use primers compatible with zinc; untreated zinc gives poor adhesion. |
| Zinc-rich paint | Restores protection at welds and damage | Functional repair, not a cosmetic color match. |
If a part is powder coated anyway and lives indoors, cold-rolled mild steel with a proper pretreatment is often the cheaper base. Galvanized sheet pays off where edges, inside faces, scratches or uncoated areas would otherwise rust.
- Surface Finish GuidePowder coat, plating and drawing callouts.
- Surface FinishingProcess overview, masking and quality notes.
Cost and lead-time drivers
Galvanized sheet is inexpensive, so labor and finishing dominate. Uretyco's sheet-metal guidance names these drivers:
- Cutting: material thickness, sheet size, cut length, pierce count, tiny holes and nesting efficiency.
- Forming: number and complexity of bends, tool changes and formed tolerances; bending adds setup, tooling, sequence planning and inspection compared with a flat cut.
- Joining and finishing: welding with zinc repair, hardware insertion, grinding, deburring and powder coating; powder color and masking can be a major lead-time driver.
- Stock and documents: common thicknesses and coatings move fastest; special thicknesses, heavier coatings or structural grades add scheduling time. Material certificates and inspection reports are opt-in, can extend the lead time and should be requested at quote time.
Galvanized steel vs. common sheet alternatives
| Material | Corrosion protection | Formability | Weldability | Weight | Relative cost |
|---|---|---|---|---|---|
| Galvanized DX51D+Z | Good; sacrificial zinc, bare cut edges | Good | Good, with fume control and zinc repair | Baseline | Baseline |
| Cold-rolled mild steel + powder coat | Depends on the coating; rusts where it is damaged | Very good | Very good before coating | Same | Similar once coated |
| Electro-galvanized steel (DC01+ZE) | Thinner zinc, smooth surface; for indoor or painted parts | Very good | Good | Same | Similar or higher |
| Aluminum 5052-H32 | Very good, incl. marine | Good | Very good | ≈ One-third | Higher |
| Stainless 304 | Excellent | Good; more springback | Excellent | Same | Much higher |
DX51D is a forming grade without a guaranteed yield strength; for load-bearing frames and brackets, ask for a structural grade such as S250GD+Z or S350GD+Z. In wet, salty or chemical environments, the zinc is consumed and stainless 304/316 or aluminum 5052 last longer.
When not to choose galvanized steel
Seawater, splash zones or chemical exposure: zinc is consumed quickly; use stainless or aluminum 5052. Visible cut edges that must stay rust-free without paint. Service above about 200 °C. Heavily welded assemblies, where fume control and zinc repair add cost: consider painted mild steel or batch hot-dip galvanizing after fabrication. Weight-critical parts. Hygienic or food-contact surfaces: use stainless steel.
Typical applications
- HVAC ducts, air-handler casings and ventilation parts.
- Electrical cabinets, control boxes and outdoor enclosures.
- Cable trays, mounting brackets and rails.
- Machine guards, covers and housings.
- Agricultural, storage and shelving equipment.
- Roofing, flashing and building sheet.
Specifying galvanized steel on Uretyco
- 1Select grade, coating and thickness
For example DX51D+Z275 (or SGCC with the coating mass in g/m²); use a structural S-grade if the part carries load.
- 2Upload DXF, STEP and drawing
A 1:1 DXF for flat parts; for bent parts a STEP plus a PDF drawing with bend direction, inside radius, visible face, weld locations and zinc-repair requirements.
- 3Define finish and documents at quote time
State powder color and environment if coated; material certificates and inspection reports are opt-in.
FAQ
Are DX51D and SGCC the same?
They are equivalent commercial forming grades: DX51D+Z under EN 10346 and SGCC under JIS G3302. Coating designations differ between the standards (JIS uses designations such as Z27 for roughly the same coating as Z275), so state the coating mass in g/m² to avoid ambiguity.
What do Z100 and Z275 mean?
The minimum total zinc mass on both sides in g/m². Z275 carries about 20 µm of zinc per side and Z100 about 7 µm. Indoor parts often use lighter coatings; outdoor parts typically Z275 or more, because coating life scales with thickness.
Will the laser-cut edges rust?
Indoors, usually not visibly. Outdoors or in condensation, the bare edges show red rust over time, more so on thicker sheet where the surrounding zinc protects the edge less. Painting or powder coating after fabrication, or batch galvanizing finished parts, protects the edges.
Can galvanized parts be welded?
Yes, but the zinc burns off and the fume is hazardous, so welding needs extraction and local coating removal, and the weld must be protected afterwards with zinc-rich paint or a coating. Spot welding, clinching and riveting are common alternatives in galvanized sheet.
Related resources
- Sheet Metal Design GuideBend radii, K-factors, hole rules and DXF hygiene.
- Sheet Metal & Laser CuttingProcess overview, files, tolerances and cost drivers.
- DXF Files for Laser CuttingHow to prepare a clean flat pattern.
- Aluminum 5052-H32Lighter, marine-grade sheet.
- Stainless Steel 304When corrosion resistance comes first.
- Designing for Lower CostStandard thicknesses, fewer bends, simpler finishes.
- Technical Drawings & TolerancesWhat belongs on the 2D drawing.
- Lead Time AnatomyWhere order time goes.
Related materials
Can't find what you need? Contact our team for expert assistance with your manufacturing project.






