C932 (UNS C93200, SAE 660) is a high-leaded tin bronze of about 83% copper, 7% tin, 7% lead and 3% zinc. It is supplied mainly as continuous-cast solid and hollow (cored) bar, which makes it the default stock for machined bushings, thrust washers and wear strips. Tin provides strength and wear resistance; the finely dispersed lead lets the bearing surface conform to the shaft and tolerate brief lapses in lubrication without seizing.
Choose C932 for plain bearings at moderate loads and speeds that are lubricated with grease or oil, and for wear parts that slide against steel. It is not self-lubricating in the way oil-impregnated sintered bronze or polymer bushings are, and its 6–8% lead content rules it out wherever lead is restricted.
Mechanical and physical properties
| Property | Typical value | Notes |
|---|---|---|
| Tensile strength (Rm) | ≈ 240–260 MPa | Continuous-cast bar; sand castings are somewhat lower. |
| Yield strength (Rp0.2) | ≈ 125–140 MPa | Bearings are sized by pressure and sliding speed rather than by yield. |
| Elongation at break | ≈ 10–20% | Varies with casting method and section size. |
| Hardness | ≈ 65 HB | Brinell, 500 kg load. Softer than steel shafts by design: the bushing is the wear part. |
| Elastic modulus | ≈ 100 GPa | About half of steel. |
| Density | ≈ 8.9 g/cm³ | Slightly heavier than steel. |
| Thermal conductivity | ≈ 58 W/m·K | Helps carry frictional heat away from the bearing. |
| Thermal expansion | ≈ 18 µm/m·K | Higher than steel (≈ 12): in a steel housing the fit tightens and running clearance shrinks as temperature rises; in an aluminum housing the fit loosens. |
| Machinability rating | 70 (C360 = 100) | Short, broken chips thanks to the lead. |
Typical room-temperature values for continuous-cast C93200 bar; castings vary with section size and foundry. For design, use the minimums of the governing standard (e.g. ASTM B505 for continuous castings, ASTM B584 for sand castings) or your material certificate.
Designing bushings and bearings
Most C932 parts are bushings, so the key questions concern load, speed, fit and lubrication rather than strength. Settle these on the drawing:
- Lubrication: provide a grease or oil supply, with a lubrication hole and groove (axial, helical or figure-eight) placed outside the most heavily loaded zone. The lead helps the bearing survive marginal lubrication; it does not replace lubrication.
- Load and speed: check the projected bearing pressure (load divided by bore diameter × length) and the sliding speed against the bearing supplier's limits for your lubrication condition.
- Running clearance: a common starting point is a diametral clearance of about 0.1% of the shaft diameter, more for grease, high temperature or misalignment. Confirm critical applications with the bearing supplier.
- Press fits: the bore of a pressed-in bushing closes by a large fraction of the interference. Either finish the bore after pressing or size it to allow for the close-in, and state which on the drawing.
- Shaft: C932 is forgiving and runs against ordinary steel shafts; a harder, smoother shaft extends bushing life. Harder bronzes such as C954 need hardened shafts.
Machining C932
With a machinability rating of 70, C932 is one of the easiest bearing alloys to machine: the lead breaks chips short and cutting forces are low. Continuous-cast bar is dense and consistent, while sand castings can contain porosity that shows up on finished bores. Watch for:
- Stock form: hollow (cored) bar close to the finished size saves material and machine time on larger bushings.
- Thin walls: thin bushings distort in clamping and when pressed in; leave enough wall for the press fit and finish critical bores in the last operation.
- Chamfers: specify lead-in chamfers on the outside diameter and bore to ease pressing and protect the shaft.
- Grooves and holes: oil grooves and lubrication holes are inexpensive to machine; define their profile and position on the drawing.
Tolerances and surface finish
Uretyco treats unspecified tolerances as ISO 2768-mK, with an as-machined surface around Ra 1.6–3.2 µm and light deburring. Bearing bores, press-fit diameters and grooves need explicit tolerances on a 2D drawing, ideally as ISO 286 fits, plus a stated Ra where it matters. Final values are confirmed in the quote and the order.
Finishing
Bearing bronze is normally supplied as-machined. Coatings do not belong on sliding surfaces, and the dull brown-gold surface oxidizes harmlessly in service. If outside surfaces need a coating for appearance or protection, mask the bore and the press-fit diameter.
Cost and lead-time drivers
Bronze bar costs more per kilogram than steel or aluminum, and bushings are often turned from stock much larger than the finished part, so material can take a larger share of the quote than the 10–30% typical for CNC parts. The main levers:
- Stock form: cored bar near net size cuts both material and machining time; standard bar sizes are widely stocked, and stock material is usually faster than a special order.
- Geometry: plain bushings and washers are quick turned parts; flanges, grooves, cross-holes and milled features add operations.
- Tolerances: tight bore and outside-diameter fits add finishing passes and inspection.
- Documents: material certificates and inspection reports are opt-in and can extend the lead time; request them at quote time.
C932 vs. common bearing materials
| Material | Load capacity | Lubrication | Machinability | Notes |
|---|---|---|---|---|
| Bronze C932 (SAE 660) | Moderate | Grease or oil; tolerates brief lapses | Very good (70) | Contains 6–8% lead. |
| Aluminum bronze C954 | High (Rm ≈ 585 MPa) | Grease or oil | Fair | Lead-free; needs a hardened shaft. |
| Oil-impregnated sintered bronze | Light to moderate | Oil held in the pores | Usually bought as standard bushings | Low maintenance for small bearings. |
| POM (Delrin) | Light | Can run dry | Excellent | Low friction; limited temperature and creep under load. |
| Brass C360 | Light | Grease or oil | Excellent (100) | Not a bearing alloy; acceptable for light, slow duty. |
For lead-free bearings, aluminum bronzes and lead-free tin bronzes are the usual substitutes. They are harder and stronger but less conformable, so they need better lubrication, alignment and shaft finish than C932.
When not to choose C932
Applications where lead is restricted: drinking water, food contact, and electrical and electronic equipment under RoHS, whose copper-alloy exemption stops at 4% lead. Dry-running bearings: use oil-impregnated sintered bronze or a polymer bushing. High, shock or oscillating loads at low speed: consider aluminum bronze. Structural or highly stressed parts: its strength is modest.
Typical applications
- Plain bearings and bushings in machinery, pumps, and agricultural and construction equipment.
- Thrust washers and wear plates.
- Slides, gibs and wear strips in machine tools.
- Pivot and linkage bushings.
- Pump and valve components for non-potable service.
Specifying C932 on Uretyco
- 1Select C932 (SAE 660)
Note CC493K or another equivalent if acceptable.
- 2Upload STEP plus a 2D drawing
Give bore and outside-diameter fits, grooves, chamfers, and whether the bore is finished before or after pressing.
- 3Request documents at quote time
Material certificates and dimensional reports must be planned before production.
FAQ
Is C932 self-lubricating?
Not in the way oil-impregnated sintered bronze or PTFE-lined bushings are. The lead improves conformability and resistance to seizure when lubrication is marginal, but C932 bearings are designed to run with grease or oil.
What is C932 called in European standards?
The closest grade is CuSn7Zn4Pb7-C (CC493K) to EN 1982, known in older German practice as Rg7. Composition limits differ slightly, so confirm equivalence when certified material is required.
What shaft should run in a C932 bushing?
Ordinary steel shafts work; a ground, harder shaft extends bushing life. Avoid bronze-on-bronze pairs, which tend to gall.
Is C932 RoHS-compliant?
Generally not. RoHS exempts copper alloys with up to 4% lead, and C932 contains 6–8%. For electrical and electronic equipment, choose a lead-free bronze or a polymer bearing.
Related resources
- Brass C360Free-cutting brass for light-duty parts.
- POM (Delrin)Dry-running polymer bushings.
- Alloy Steel 4140Hardenable steel for shafts and pins.
- CNC Design GuideTolerances, walls, threads and setups.
- CNC MachiningProcess overview, files and cost drivers.
- Technical Drawings & TolerancesWhat belongs on the 2D drawing.
- Quality Control & InspectionInspection scope, reports and certificates.
- Lead Time AnatomyWhere order time goes.
Related materials
Can't find what you need? Contact our team for expert assistance with your manufacturing project.






