Uretyco
Make it now
PolyJet Rigid Opaque (Vero family)

PolyJet Rigid Opaque (Vero family)

Plastics
PolyJetVeroResin

PolyJet rigid opaque (Vero family) photopolymer reference: typical properties, design rules, support and surface options, color and multi-material printing, cost drivers, and comparison with SLA, MJF and FDM.

PolyJet prints parts by jetting droplets of liquid photopolymer layer by layer and curing each layer immediately with UV light, much like an inkjet printer. The rigid opaque materials, the Vero family on Stratasys printers, are acrylic-based photopolymers in white, black, grey, blue and full color. On multi-material printers they can be combined in one build with rubber-like materials to create intermediate 'digital materials'.

Choose it when appearance and detail matter more than strength: presentation models, form-and-fit checks, ergonomic mock-ups, anatomical models and master patterns for silicone molds. It is not a production plastic: parts are relatively brittle, soften at about 45–50 °C and age under UV light.

Mechanical and physical properties

PropertyTypical valueNotes
Tensile strength≈ 50–65 MPaASTM D638, printed test bars.
Elongation at break≈ 10–25%Varies with material and orientation.
Tensile modulus≈ 2.0–3.0 GPaStiffness similar to ABS.
Flexural strength≈ 75–110 MPaASTM D790.
Notched Izod impact≈ 20–30 J/mBrittle; far below molded ABS.
Heat deflection temperature≈ 45–50 °CAt 0.45 MPa; parts soften in a hot car or next to warm electronics.
Hardness≈ 83–86 Shore DHard, scratch-resistant surface.
Density≈ 1.17–1.18 g/cm³Cured material.
Layer thickness≈ 15–30 µmDepends on printer and print mode.
Typical values, not design allowables

Typical datasheet values for Vero-family materials on Stratasys printers, measured on printed test bars. Real parts vary with material, print mode, orientation, post-processing and age; photopolymers keep changing with UV exposure and time.

Designing for PolyJet

PolyJet builds overhangs and cavities on a support material, so geometric freedom is high but support consumption drives cost. General PolyJet design guidance, confirmed in the quote:

  • Walls and details: walls of about 1 mm and up print reliably; thinner walls and fine pins are possible but fragile during support removal.
  • Support removal: gel-like support is removed by water jet, soluble support in a bath. Avoid long, narrow internal channels and closed cavities that support cannot leave.
  • Glossy or matte: faces that touch support come out matte, while upward-facing faces can be glossy. Orient visible faces accordingly, or ask for matte overall for an even look.
  • Fits: leave clearance between mating parts and validate fit-critical features on a prototype, as Uretyco's 3D-printing guidance recommends for all printed parts.
  • Threads and inserts: printed threads in brittle Vero are weak; use inserts or post-machining for reliable function.
  • Color and multi-material: rigid and rubber-like regions or colors are assigned per body or region. Upload separate bodies or a 3MF file, which Uretyco prefers when color or multi-body data matters.

Tolerances and surface

Uretyco's 3D-printing guidance ties printed tolerance to technology, material shrinkage, orientation, part size, support strategy and post-processing, and recommends testing fit-critical features before production; final values are confirmed in the quote. PolyJet's very thin layers give one of the smoothest as-printed surfaces in 3D printing, with layer lines barely visible on glossy faces; large, flat parts can still warp slightly.

Finishing options

PolyJet parts often need little finishing; when they do, it is mostly cosmetic.

FinishWhat it addsNotes for Vero
As printed, glossyShine on upward facesFaces that touched support stay matte.
As printed, matteUniform appearanceEvery face has support contact; uses slightly more support material.
Light sanding and polishingSmoother, more even surfaceRemoves support marks on visible faces.
Primer and paintExact color, production lookTypical for presentation models; painting is one of Uretyco's listed printing post-processes.
InsertsDurable threadsHeat-set or press-fit inserts; drill or ream holes for fits.
Treat them as models

Vero parts discolor and become more brittle with long UV exposure and soften at moderate heat. Keep display models out of direct sun, hot cars and lamps, and do not use them as functional brackets or clips.

Cost and lead-time drivers

PolyJet is one of the more expensive printing processes per part. Uretyco's 3D-printing guidance names the drivers:

  • Part volume, bounding box, print orientation, support material, nesting efficiency and machine time. On PolyJet, support can account for a large share of material use.
  • Material technology and post-processing such as sanding or painting; multi-material, digital-material and full-color builds cost more than single-material prints.
  • Dense, bulky models that could be hollowed or redesigned.
  • Lead time: small parts in common materials can be fast; special materials, large parts, support-heavy geometry and painting add time.

PolyJet vs. common printing alternatives

Material and processSurface and detailToughnessHeat resistanceColor and multi-materialRelative cost
PolyJet rigid (Vero)ExcellentLow; brittleLow (HDT ≈ 45–50 °C)Full color, rigid plus flexibleBaseline (high)
Standard SLA resinExcellentLow to moderateLow to moderateSingle materialLower
MJF / SLS PA12Good; slightly grainyGood; durableModerateSingle material; can be dyedSimilar or lower
FDM (PLA, ABS)Visible layer linesModerateLow (PLA) to moderate (ABS)Single or limitedLowest

Choose SLA when a smooth single-color model is enough, MJF or SLS when the part must work mechanically, FDM for cheap early concepts, and PolyJet when color, multi-material regions or the finest surface on a visual model justify the cost.

When not to choose PolyJet rigid

Common mismatches

Load-bearing, snap-fit or impact parts. Service above about 45–50 °C. Long outdoor or window-side exposure. End-use production parts. Food or skin contact: standard Vero materials are not certified for it; dedicated biocompatible PolyJet materials are separate grades. Large parts, where support and build time make cost climb quickly.

Typical applications

  • Presentation and marketing models.
  • Form, fit and ergonomics checks.
  • Multi-material prototypes that simulate overmolded grips.
  • Anatomical and planning models.
  • Master patterns for silicone molds and cast urethane.
  • Color concept models and detailed miniatures.

Specifying PolyJet on Uretyco

  1. 1
    Choose PolyJet rigid, color and surface

    State the color, glossy or matte, and whether any region should be rubber-like.

  2. 2
    Upload STL or 3MF

    Use 3MF when color or multi-body data matters; STEP is also useful for review. Add a PDF drawing for inserts or critical dimensions.

  3. 3
    Describe the use

    Tell the assistant whether the part is a visual model, a fit check or a master pattern so technologies and finishes can be compared.

FAQ

PolyJet or SLA?

Both give smooth, detailed parts. SLA is usually cheaper for single-color models and offers tougher and higher-temperature resins. PolyJet wins when you need several colors, rigid and rubber-like regions in one part, or a glossy as-printed finish.

Can PolyJet parts be used as functional parts?

Only for light-duty checks. Vero is brittle, softens at about 45–50 °C and ages under UV light. For functional prototypes, use MJF or SLS nylon, or machined plastics.

Can PolyJet parts serve as master patterns?

Yes. The smooth surface and fine detail suit masters for silicone molds and cast urethane. Every mark on the master transfers to the cast parts, so specify the required surface on visible faces.

Which colors are available?

Vero materials come in white, black, grey and blue, and full-color printers can produce many colors in one part. Printed colors are not an exact RAL match; for exact color, paint the part.

Related materials

Plastics

Standard SLA

General-purpose photopolymer for SLA and DLP printing: the smoothest surfaces and finest detail of any common 3D printing process, but brittle and heat-sensitive. The default for cosmetic prototypes, detailed models and casting masters.

Plastics

ABS-Like Resin

Toughened photopolymer, mainly for MSLA printers, that is less brittle than standard resin while keeping fine detail and smooth surfaces. For handled and assembled prototypes, housings and detailed models; not a substitute for real ABS.

Plastics

Castable Resin

Photopolymer that burns out cleanly in the investment casting flask, so a printed pattern replaces a wax model. For jewelry, dental frameworks and small precision castings in gold, silver, bronze and cobalt chrome; patterns need a resin burnout schedule.

Plastics

Clear Resin

Unpigmented photopolymer for SLA, DLP and MSLA that prints translucent and becomes close to transparent after sanding and polishing or a clear coat. For see-through prototypes, fluidic models and light covers; brittle and prone to yellowing.

Plastics

Dental Resin

Photopolymers for dentistry: accurate model resins and biocompatible grades for guides, splints and temporary crowns. Use in the mouth depends on the certified resin, a validated printer and post-processing workflow, and the device maker's regulatory duties.

Plastics

High-Temp Resin

Heat-resistant photopolymer for SLA and DLP printing, reaching an HDT of roughly 100–250 °C or more after thermal post-cure. Used for low-volume mold inserts, heat-exposed fixtures and hot air or fluid flow tests; stiff but brittle.

Was this page helpful?

Can't find what you need? Contact our team for expert assistance with your manufacturing project.

Contact our team