Uretyco
Make it now

Die Casting

High-pressure die casting for zinc, aluminum, and magnesium alloys: how it works, when it beats machining, design rules for draft, walls and radii, porosity control, secondary machining and finishing, cost and lead-time drivers.

Overview

Die casting forces molten non-ferrous metal (zinc, aluminum, or magnesium alloys) into a hardened steel die under high pressure. The metal solidifies quickly, the die opens, and the casting is ejected with thin walls, ribs, bosses, and mounting features already formed. Because the shape comes from the die, parts repeat closely and need far less material removal than parts machined from solid stock.

Like injection molding, die casting trades a significant up-front die cost for a low price per part. It is the right choice at moderate to high volumes once the design is stable; for prototypes and low volumes, CNC machining is usually faster and cheaper.

How it works

  1. 1
    Die design and DFM review

    Draft, wall thickness, radii, parting line, gate and overflow positions, and ejector locations are defined; undercuts are designed out or given slides.

  2. 2
    Die manufacturing

    The die halves are machined from hardened tool steel, with cooling channels, cores, and any slides.

  3. 3
    Casting

    Zinc alloys run on hot-chamber machines; aluminum alloys run on cold-chamber machines, where metal is ladled into a shot sleeve for every shot. Magnesium can run on either, depending on part size.

  4. 4
    Trimming and secondary operations

    Runners, overflows, and flash are trimmed off; critical features are machined, and the parts are finished, inspected, and packed.

When to choose

  • Moderate to high volumes, where the die cost is spread over enough parts to beat machining from bar or plate.
  • Thin walls, ribs, bosses, and mounting features integrated into one casting instead of a welded or bolted assembly.
  • Housings, heat sinks, connectors, brackets, and enclosures in zinc, aluminum, or magnesium alloys.
  • Cosmetic metal parts, provided flash removal and the finishing plan are defined up front.

When not to choose

  • Prototypes and design iterations: machine the part until the design is stable.
  • Steel or stainless steel parts: die casting is limited to non-ferrous alloys.
  • Parts that must be welded or solution heat-treated (T6) after casting, unless alloy and process are chosen for it.
  • Pressure-tight or highly stressed parts without a defined porosity acceptance and test plan.
  • Very thick, solid sections: they trap porosity and lengthen the cycle; core them out or choose another process.

Required files

FileUseNotes
STEP/STPCast geometry, including draftRequired for die design and DFM analysis.
PDF drawingAlloy, tolerances, machined features and allowances, datum scheme, finish, porosity or leak-test requirementsStrongly recommended before the die is cut.
Reference sampleCosmetic or fit benchmarkUseful when matching an existing part.

Design rules

  • Keep walls as uniform as possible and change thickness gradually; thick sections and abrupt transitions are where porosity forms.
  • Core out heavy sections and add ribs for stiffness instead of mass.
  • Add draft to all surfaces parallel to the die opening. Inner walls and cores need more draft than outer walls, because the metal shrinks onto them as it cools.
  • Use generous fillets and radii at every junction; sharp corners disturb metal flow, concentrate stress, and shorten die life.
  • Avoid undercuts where possible; each one needs a slide, which adds die cost and maintenance.
  • Define the parting line and the gate, overflow, and ejector-pin locations relative to cosmetic and sealing faces.
  • Avoid tight dimensions across the parting line or moving slides; they vary more than dimensions within one die half.
  • Add a machining allowance and a clear datum scheme for every feature that will be machined after casting.

Typical alloys

Alloy familyCommon examplesTypical reason to choose
ZincZamak 3, Zamak 5Fills thin walls and fine detail well, is a good base for plating, and gives long die life because it casts at a lower temperature; dense, so best for smaller parts.
AluminumA380, ADC12, EN AC-46000 (AlSi9Cu3)Light and strong for structural housings, enclosures, and heat sinks; the most widely used die-casting family.
MagnesiumAZ91DLightest structural metal; thin-walled housings where weight matters most.

Aluminum A356 is a sand, investment, and permanent-mold casting alloy that is usually heat-treated to T6; it is not a typical high-pressure die-casting alloy. If you need A356-type properties, say so in the order notes, which go to the manufacturing partner with the part.

Porosity and process risks

The die fills in a fraction of a second, so trapped air and shrinkage can leave small voids (porosity), mostly in thick sections and at abrupt wall transitions. Some porosity is normal in die castings; it matters most for pressure-tight parts and for surfaces that will be machined, because machining can open pores below the dense outer skin.

  • Design for uniform walls and agree on gate, venting, and overflow positions with the supplier; vacuum-assisted casting reduces gas porosity where it is available.
  • For pressure-tight parts, state the leak-test requirement and the porosity acceptance on the drawing; impregnation can seal porosity after machining.
  • Conventional die castings are usually not solution heat-treated or welded, because entrapped gas can cause blistering. Confirm mechanical targets against the supplier's alloy data.
  • Keep machining allowances small on surfaces where the dense outer skin matters.

Secondary operations and finishing

Critical sealing surfaces, bearing bores, and datum features often receive light machining after casting, so include machining allowances and datum schemes on the drawing. Other common steps are trimming, deburring or vibratory finishing, tapping, impregnation, and surface finishing.

FinishNotes for die castings
Powder coating or paintingCommon for aluminum and zinc housings. Needs a clean, pretreated surface; gas escaping from porosity during curing can cause defects, so mention it if parts will be coated.
Plating (e.g. nickel, chrome)Zinc die castings are a classic base for decorative plating; surface quality before plating decides the result.
AnodizingPossible on die-cast aluminum, but high-silicon die-casting alloys anodize unevenly and gray; for cosmetic anodizing, machined 6061 is more consistent.
Chromate conversion coatingCorrosion protection and paint base with negligible build-up; the surface stays electrically conductive.

Tolerance expectations

As-cast tolerance depends on the alloy, the part size, and whether a dimension lies within one die half or crosses the parting line or a slide. Die-casting tolerances are confirmed per part in the quote: specify critical dimensions on the drawing and plan machining for fits, bores, and sealing faces.

RequirementTypical guidanceCost impact
Dimensions within one die halfAs cast, per drawing and supplier capabilityLow
Dimensions across the parting line or slidesAllow more variation, or machine after castingMedium
Bores, fits, sealing facesMachine after casting; specify allowance and datumsMedium to high
Pressure tightnessDefine leak test and porosity acceptance; impregnate if neededMedium to high
Quote-dependent values

Tolerance, finish, material, inspection, and lead-time values are practical guidance. Binding values are those confirmed in your quote and order, based on the material, drawing and production method.

Cost drivers

  • The die: size, number of cavities, slides for undercuts, cooling, and steel grade. It is a significant one-time cost, so quantity decides whether die casting pays off.
  • The part: alloy, part weight, the machine size needed for the projected area, and cycle time.
  • Trimming, deburring, machining, tapping, and impregnation after casting.
  • Finishing, masking, and cosmetic acceptance criteria.
  • Inspection: first-article reports, CMM measurement, leak testing, or X-ray inspection where porosity matters.

Lead-time drivers

  • Die design, manufacture, and sampling dominate the first delivery; repeat orders on an existing die mainly wait for the production queue.
  • First-article approval and any die corrections happen before production is released.
  • Machining, impregnation, and finishing are separate operations that add time after casting.
  • Inspection reports and material documentation are opt-in and add time; request them at quote time.

Die casting versus alternatives

ProcessBest forToolingUnit cost at volumeNotes
Die castingModerate to high volumes of thin-walled non-ferrous partsHardened steel die, high costLowNear-net shape; porosity must be managed
CNC machiningPrototypes, low volumes, tight tolerancesNoneHighBest dimensional control; any machinable metal
Sand castingLow volumes, large or heavy partsPattern, low costMediumRougher surface, thicker walls, more machining
Investment castingComplex shapes; wider alloy range including steelsWax-pattern tooling, medium costMediumGood surface and detail; slower cycle
Sheet metal fabricationBrackets, panels, and enclosures from flat stockLittle or noneLow to mediumLimited to formed sheet geometry

Upload the model and describe quantity and function: the quote engine scores casting alongside CNC machining and sheet metal, and the assistant can explain the tradeoff for your part.

Uretyco AI workflow

  1. 1
    Geometry analysis

    Uretyco checks wall thickness, thick sections, draft, undercuts, and features that will need machining.

  2. 2
    Volume and alloy questions

    The assistant asks about annual quantity, alloy, pressure tightness, finish, and which features are critical.

  3. 3
    Process comparison

    Die casting is compared with machining and other routes on die cost, unit price, and lead time.

  4. 4
    First article and production

    Initial castings are reviewed before the full run; parts are then cast, trimmed, machined, finished, and inspected to the agreed scope.

Quality notes

  • Mark the sealing faces, bores, and datum features that will be machined, and state the allowances.
  • Define porosity acceptance and any leak or pressure test for fluid-carrying parts.
  • Request first-article approval before the full run. Material certificates are opt-in: ask for them at quote time if you need them.
  • Mark cosmetic surfaces and acceptable locations for parting-line, gate, and ejector marks.

FAQ

Zinc or aluminum?

Zinc fills thin walls and fine detail best, plates well, and gives long die life, but it is about two and a half times as dense as aluminum, so it suits smaller parts. Aluminum is the choice for lightweight structural housings and heat sinks; magnesium when weight is critical.

Can die castings be heat-treated or welded?

Conventional high-pressure die castings usually are not solution heat-treated or welded, because gas trapped in the casting expands and causes blisters. If the part needs T6 properties or welding, choose an alloy and process that allow it; the DFM findings show how well the part suits the process.

Is A356 a die-casting alloy?

Not typically. A356 is used for sand, investment, and permanent-mold castings and is usually heat-treated to T6. Typical high-pressure die-casting alloys are A380, ADC12, or EN AC-46000 for aluminum and Zamak 3 or Zamak 5 for zinc.

When is CNC machining the better choice?

When quantities are low, the design is still changing, or many features need tight tolerances. Machining needs no die and gives the best dimensional control, and cast parts often need machining on their critical features anyway.

Was this page helpful?

Can't find what you need? Contact our team for expert assistance with your manufacturing project.

Contact our team